• May 23, 2022

Are Quando Hubs Any Good?

Are quando hubs any good? With good quality grease and good setup on the cones and lockrings, it's a good, fairly aerodynamic hub. I bought these as part of a wheel set last winter. After about 300 miles the hub broke and they are not rebuildable.

How do I remove a quando freehub?

  • Remove set screw from side of drive side locknut.
  • Hold non-drive side cone with cone wrench. Loosen and remove drive side locknut.
  • Pull freehub to remove. Use care not to loose small parts. Note orientation of pawls as you remove freehub.
  • How do I make my free hub louder?

    Are DT Swiss 350 hubs loud?

    The Hope hub was really loud, which usually wouldn't be a deterrent. But, after a demo day at a LBS and riding a bike with the DT 350 hub and hearing how quiet it was, it quickly became a consideration. I went with the DT hub and after a few rides, this thing is almost silent.

    Why does my bike click when I pedal hard?

    A clicking noise is the most common sound your bike can make. It can be due to the rider pedaling fast, and the chain wants to jump up and down the rear cassette to accommodate the demands of the pedal. To identify the sound, you can slow down from pedaling and observe whether you still hear a sound.


    Related guide for Are Quando Hubs Any Good?


    Why do some bikes make noise when coasting?

    A spring-loaded part that engages a set of teeth when moving in one direction, but slides over them when moving in the other direction. The pawls in a freewheel make a ticking sound when a bicycle coasts. Most freewheels have two or three pawls.


    Should I grease my bottom bracket?

    new grease won't cure worn out bearings and races. so, to answer the original question, no, you don't need to lube the bottom bracket.


    When should I repack my hubs?

    When they are freshly packed pay attention to how easily the wheels spin when you hold them off the road or the bike is upside down. Then do this every so often and if they seem to be getting even the least bit slower then it is time to pack.


    How do I know if my bike bearings are bad?

    Worn out or dry bearings will feel rough, metallic and dry. Sometimes they're so dry that if you pull your finger fast across the axle you can make the axle keep spinning because there's no grease inside the bearings to slow it down.


    Which is better freewheel or cassette?

    A freewheel has a lower number of gears so is better suited for casual riders who don't require the larger selection of gears available from a cassette. It's much better coasting, allowing you to rest your legs, and if done correctly, can be useful when climbing hills and easier coming down them.


    What is the difference between DT Swiss 240 and 350?

    The DT Swiss 350 line offers the same manufacturing quality and design features found in its higher end counterpart, the DT Swiss 240s. The main difference between the hub lines stems from the fact that the 240s has been machine optimized for weight savings and the 350 has not.


    Is more Pawls better?

    The number of pawls can also vary between designs, but in general the more the better. Big teeth and pawls will deal better with larger amounts of torque, but on the other hand a finer set up will give you faster engagement.


    How do I make my DT Swiss hub louder?


    Why do bikes rattle?

    RATTLES. Symptoms: A consistent rattle or clicking sound at the front of your bike could be caused by your cables. This is often due to a poor initial setup where excess wire was left at the front end of the bike. During your ride, the cables can click against each other or the frame.


    Why are my cranks creaking?

    Cranks. The most common cause of creaking is the crank being loose on the spindle. Remove the crank bolts, lubricate the threads and under the bolt head, and reinstall. Tighten the bolts to the manufacturer recommended torque.


    Why do new bikes squeak?

    Creaking each time you pedal is often a sign of something being up with your bottom bracket. Annoyingly, this often means disassembling everything for cleaning and regreasing. If the parts are new, this is often enough on its own, although there's also the possibility of the components being worn out.


    Why do BMX bikes click?

    Why Does My BMX Bike Click When I Pedal? A BMX bike clicks when you pedal because the chain is hitting the case, the hub bearing needs fixing, or there's a problem with the chainstay. It's likely also that there might be a crack on the axle or the front wheel needs fixing.


    Can you stop pedaling on a spin bike?

    The short answer is no. On the fixed gear bicycle pedals and rear wheel are directly connected, meaning when the rear wheel is spinning, pedals are spinning as well. Due to this, you cannot coast on the fixed gear bicycle and have to pedal every time the bike is moving.


    How many miles should a bottom bracket last?

    Simple rule is (unless you're starting a long trip) "if it ain't broke don't fix it". Do normal maintenance, keep things properly lubed and your BB should last for another 4,000 miles or more.


    How long do bike wheel bearings last?

    How long does a wheel bearing last? Wheel bearings have an average lifespan of 136,000 to 160,000 km (approximately 85,000 to 100,000 miles). This is only a rule of thumb though, the actual lifespan of a wheel bearing depends on the quality of the wheel bearing and the operating conditions.


    How often should you grease bike hubs?

    Best practice 1-2 years depending on use and grease quality. If you're cycling in a lot of rain or off-road 3-9 months is a better bet. If it's a cheap bb and you don't care about failure then let it eat so long as it's adjusted and running smooth.


    Was this post helpful?

    Leave a Reply

    Your email address will not be published.